View FTLX1412M3BNL_8029690.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

f i n i s a r ? finisar corporation 25-oct-10 rev a1 page 1 product specification rohs-6 compliant extended temperature 10gb/s 10km xfp optical transceiver FTLX1412M3BNL product features ? supports 9.95gb/s to 11.35gb/s bit rates ? extended temperature range: -5c to 85c ? rohs-6 compliant (lead-free) ? hot-pluggable xfp footprint ? single power supply: 3.3v ? maximum link length of 10km ? uncooled 1310nm dfb laser ? duplex lc connector ? no reference clock required ? built-in digital diagnostic functions ? standard bail release mechanism applications ? sonet oc-192 sr-1 sdh stm i-64.1 ? 10gbase-lr/lw 10g ethernet ? 1200-sm-ll-l 10g fibre channel ? 10gbase-lr/lw with fec ? 1200-sm-ll-l 10g fibre channel with fec finisar?s FTLX1412M3BNL extended temperature small form factor 10gb/s (xfp) transceivers are compliant with the current xfp multi-source agreement (msa) specification 1 . they comply with sonet oc- 192 sr-1, sdh stm i-64.1, 10-gigabit ethernet 10gbase-lr/lw per ieee 802.3 ae, 10g fibre channel 1200-sm-ll-l. digital diagnostics functions are available via a 2-wire serial interface, as specified in the xfp msa. the transceiver is rohs comp liant and lead free per directive 2002/95/ec 3 , and finisar application note an-2038 4 . product selection FTLX1412M3BNL
FTLX1412M3BNL multirate xfp product specification ? october 2010 f i n i s a r ? finisar corporation 25-oct-10 rev a1 page 2 i. pin descriptions pin logic symbol name/description ref. 1 gnd module ground 1 2 vee5 optional ?5.2 power supply ? not required 3 lvttl-i mod-desel module de-select; when held low allows the module to respond to 2-wire serial interface commands 4 lvttl-o interrupt interrupt (bar); indicates pres ence of an important condition which can be read over the serial 2-wire interface 2 5 lvttl-i tx_dis transmitte r disable; transmitter laser source turned off 6 vcc5 +5 power supply? not required 7 gnd module ground 1 8 vcc3 +3.3v power supply 9 vcc3 +3.3v power supply 10 lvttl-i scl serial 2-wire interface clock 2 11 lvttl- i/o sda serial 2-wire interface data line 2 12 lvttl-o mod_abs module absent; indicates module is not present. grounded in the module. 2 13 lvttl-o mod_nr module not ready; finisar defines it as a logical or between rx_los and loss of lock in tx/rx. 2 14 lvttl-o rx_los receiver lo ss of signal indicator 2 15 gnd module ground 1 16 gnd module ground 1 17 cml-o rd- receiver inverted data output 18 cml-o rd+ receiver non- inverted data output 19 gnd module ground 1 20 vcc2 +1.8v power supply ? not required 21 lvttl-i p_down/rst power down; when high, places the module in the low power stand-by mode and on the falling edge of p_down initiates a module reset reset; the falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. 22 vcc2 +1.8v power supply ? not required 23 gnd module ground 1 24 pecl-i refclk+ reference clock non-inverted input, ac coupled on the host board ? not required 3 25 pecl-i refclk- reference clock inverted input, ac coupled on the host board ? not required 3 26 gnd module ground 1 27 gnd module ground 1 28 cml-i td- transmitter inverted data input 29 cml-i td+ transmitter non-inverted data input 30 gnd module ground 1 notes : 1. module circuit ground is isolated from module chassis ground within the module. 2. open collector; should be pulled up with 4.7k ? 10kohms on host board to a voltage between 3.15v and 3.6v. 3. a reference clock input is not required by the FTLX1412M3BNL. if present, it will be ignored.
FTLX1412M3BNL multirate xfp product specification ? october 2010 f i n i s a r ? finisar corporation 25-oct-10 rev a1 page 3 diagram of host board connector block pin numbers and name ii. absolute maximum ratings parameter symbol min typ max unit ref. maximum supply voltage vcc3 -0.5 4.0 v storage temperature t s -40 85 c case operating temperature t op -5 85 c
FTLX1412M3BNL multirate xfp product specification ? october 2010 f i n i s a r ? finisar corporation 25-oct-10 rev a1 page 4 iii. electrical characteristics (t op = -5 to 85 c, v cc3 = 3.13 to 3.46 volts) parameter symbol min typ max unit ref. supply voltage vcc3 3.13 3.46 v supply current (-10c to +85c case) icc3 1 600 ma supply current (-40c to -10c case) icc3 2 650 ma module total power (-10c to +85c case) p 1 2.0 w 1 module total power (-40c to -10c case) p 2 2.5 w 1 transmitter input differential impedance r in 100 2 differential data input swing vin,pp 120 820 mv 3 transmit disable voltage v d 2.0 vcc v 4 transmit enable voltage v en gnd gnd+ 0.8 v transmit disable assert time 10 us receiver differential data output swing vout,pp 340 650 850 mv 5 data output rise time t r 38 ps 6 data output fall time t f 38 ps 6 los fault v los faul t vcc ? 0.5 vcc host v 7 los normal v los nor m gnd gnd+0.5 v 7 power supply rejection psr see note 8 below 8 notes : 1. maximum total power value is specified across the indicated temperature and voltage ranges. 2. after internal ac coupling. 3. sonet/sdh jitter generation requirements are guaranteed with a minimum differential data input swing of 500mv peak-to-peak. 4. or open circuit. 5. into 100 ohms differential termination. 6. 20 ? 80 % 7. loss of signal is open collector to be pulled up with a 4.7k ? 10kohm resistor to 3.15 ? 3.6v. logic 0 indicates normal operation; logic 1 indicates no signal detected. 8. per section 2.7.1. in the xfp msa specification 1 .
FTLX1412M3BNL multirate xfp product specification ? october 2010 f i n i s a r ? finisar corporation 25-oct-10 rev a1 page 5 iv. optical characteristics (t op = -5 to 85 c, v cc3 = 3.13 to 3.45 volts) parameter symbol min typ max unit ref. transmitter output opt. pwr: 9/125 smf p out -6 -1 dbm 1 optical wavelength 1260 1355 nm optical extinction ratio er 6 db 1 sidemode supression ratio ssr min 30 db tx jitter generation (peak-to-peak) tx j 0.1 ui tx jitter generation (rms) tx jrms 0.01 ui relative intensity noise rin -130 db/hz receiver receiver sensitivity @ 10.5gb/s r sens1 -14.4 dbm 2 receiver sensitivity @ 11.3gb/s r sens2 -13.4 dbm 2 stressed receiver sensitivity (oma) @ 10.5gb/s r sens3 -10.3 dbm 3 maximum input power p max +0.5 dbm optical center wavelength having er = 6 db guarantees that the ?6 dbm minimum output power meets ieee 802.3ae requirement of oma=-5.2dbm. 2. measured with worst er; ber<10 -12 ; 2 31 ? 1 prbs. complies with ?12.6 dbm oma at er = 6 db. 3. per ieee 802.3ae. equivalent to ?13.3 dbm average power at infinite er, -11.08 dbm at er = 6 db.
FTLX1412M3BNL multirate xfp product specification ? october 2010 f i n i s a r ? finisar corporation 25-oct-10 rev a1 page 6 v. general specifications parameter symbol min typ max units ref. bit rate br 9.95 11.3 gb/s 1 bit error ratio ber 10 -12 2 max. supported link length l max 10 km 1 notes : 1. sonet oc-192 sr-1, sdh stm i-64.1, 10gbase- lr/lw, 1200-sm-ll-l, sonet oc-192 with fec, 10gbase-lr/lw + fec, 1200-sm-ll-l + fec. 2. tested with a 2 31 ? 1 prbs vi. environmental specifications finisar FTLX1412M3BNL transceivers have an extended operating case temperature range of -5c to +85c. parameter symbol mi n typ max units ref. case operating temperature t op -5 85 c storage temperature t sto -40 85 c vii. regulatory compliance finisar xfp transceivers are class 1 laser products. they are certified per the following standards: feature agency standard certificate number laser eye safety fda/cdrh cdrh 21 cfr 1040 and laser notice 50 9210176-77 laser eye safety tv en 60825-1: 2007, en60825-2:2004+a1 iec 60825-1: 2007 (2 nd edition) iec 60825-2: 2010 (3 rd edition) 72101686 electrical safety tv en 60950:2006+a11 72101686 electrical safety ul/csa class 3862.07 class 3862.87 2283290 copies of the referenced cer tificates are available at fi nisar corporation upon request.
FTLX1412M3BNL multirate xfp product specification ? october 2010 f i n i s a r ? finisar corporation 25-oct-10 rev a1 page 7 viii. digital diagnostic functions as defined by the xfp msa 1 , finisar xfp transceivers provide digital diagnostic functions via a 2-wire serial interface, wh ich allows real-time access to the following operating parameters: ? transceiver temperature ? laser bias current ? transmitted optical power ? received optical power ? transceiver supply voltage it also provides a sophisticated system of al arm and warning flags, which may be used to alert end-users when particular operating para meters are outside of a factory-set normal range. the operating and diagnostics information is monitored and reported by a digital diagnostics transceiver controller (ddtc) inside the transceiver, which is accessed through the 2-wire serial interf ace. when the serial protocol is activated, the serial clock signal (scl pin) is generated by the host. the positive edge clocks data into the xfp transceiver into those segments of its memo ry map that are not write-protected. the negative edge clocks data from the xfp transcei ver. the serial data signal (sda pin) is bi-directional for serial data transfer. th e host uses sda in conjunction with scl to mark the start and end of serial protocol activation. the memories are organized as a series of 8-bit data words th at can be addressed individua lly or sequentially. the 2-wire serial interface provides sequential or random access to the 8 bit parameters, addressed from 000h to the maximum address of the memory. for more detailed information including me mory map definitions, please see finisar application note an-2035 ?digital diagnosti c monitoring interface for xfp optical transceivers?, or the xfp msa specification 1 .
FTLX1412M3BNL multirate xfp product specification ? october 2010 f i n i s a r ? finisar corporation 25-oct-10 rev a1 page 8 ix. mechanical specifications finisar?s xfp transceivers are compliant w ith the dimensions defined by the xfp multi- sourcing agreement (msa). xfp transceiver (dimensions are in mm) unl a tch ed 8.50 13.30 16.00 20.85 39.00 r1.00 la tche d 18.35 77.95 22.15
FTLX1412M3BNL multirate xfp product specification ? october 2010 f i n i s a r ? finisar corporation 25-oct-10 rev a1 page 9 x. pcb layout and bezel recommendations xfp host board mechanical layout (dimensions are in mm)
FTLX1412M3BNL multirate xfp product specification ? october 2010 f i n i s a r ? finisar corporation 25-oct-10 rev a1 page 10 xfp detail host board mechanical layout (dimensions are in mm) xfp recommended bezel design (dimensions are in mm)
FTLX1412M3BNL multirate xfp product specification ? october 2010 f i n i s a r ? finisar corporation 25-oct-10 rev a1 page 11 xi. references 1. 10 gigabit small form factor pluggabl e module (xfp) multi-source agreement (msa), rev 4.5 ? august 2005. document ation is currently available at http://www.xfpmsa.org/ 2. application note an-2035: ?digital di agnostic monitoring interface for xfp optical transceivers? ? finisa r corporation, december 2003 3. directive 2002/95/ec of the european council parliament and of the council, ?on the restriction of the use of certain hazardous substances in electrical and electronic equipment?. january 27, 2003. 4. ?application note an-2038: finisar im plementation of rohs compliant transceivers?, finisar corporation, january 21, 2005. xii. revision history revision date description a1 10/25/2010 ? document created xiii. for more information finisar corporation 1389 moffett park drive sunnyvale, ca 94089-1133 tel. 1-408-548-1000 fax 1-408-541-6138 sales@finisar.com www.finisar.com

▲Up To Search▲

Price & Availability of FTLX1412M3BNL

	To Download FTLX1412M3BNL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .